| Technicalparameters |
| No. | Project | Standard |
| 1 | Spindle blowing dust/seal gas pressure(MPa) | 0.2-0.25 |
| 2 | Spindle gas seal gas flow (L/min) | 65±10(When onWorking) |
| 3 | Cooling water pressure(MPa) | ≧0.25 |
| 4 | Cooling water flow(L/min) | ≧2.5 |
| 5 | Cooling water temperature(℃) | 24-28 |
| 6 | Spindle static state pulse(µm) | ≦3 |
| 7 | Spindle vibration(mm/s) | ≦1.0 |
| 8 | Spindle assembly method | Bottom mounting(6-M8) |
| 9 | Motor windingsPressure test(V/M) | 1000V/1 minute withstanding Voltage test |
| 10 | Tool InterfaceTool Interface | BT30 |
| 11 | Inverter Specifications | 5.5KW(220V) |
| 12 | Fitment | Woodworking machinery, polishing industry, etc. |
5.Spindle installation explanationSpindle installation explanation
1)Fan cooling system description
When
the spindle rotates, the rear fan system must be started to ensure the
correct supply voltage and the supply voltage is 12V.
2)Air sealing control(AS)
In
order to prevent water or impurities enters internal of the
spindle,spindle will have gas sealing device,the gas seal machine must
be started start with the machine at the same time.And the need to go
throughmulti-stage filtration.
3)Compressed gas quality requirements
The quality requirement of gas which is used in gas seals:
Oil content:﹤0.01mg/m³
Solid particle:﹤5µ m
Pressure dew point:﹤7.5℃(0.7MPa)
4)Running-in program instructions
Only
all monitoring issued no failures operational signals,at the same
time,all safety devices have been installed and working properly,then
allow start spindle.
Note:new
or spindlewhichis not used for a long time must to be running
slowly.First,start run spindle for half an hour as 25% of the maximum
speed,then increaseto50% of the maximum speed,to run 15
minutes,finally,increase to maximum speed.It’s need to check the temperature of the spindleduring the wholeprocess,spindle
will get hot, but not hot hand, if the spindle becomes hot, pls stop
the operation and contact our customer service department.
5)Product backend interface instructions
| No. | Function | Definition |
| 1 | Gassealing(Protection of impurities into the spindle0.2-0.25MPa) | Ф6 |
| 2 | Return air(piston reset 0.35-0.45MPa) | Ф6 |
| 5 | Power supply(Spindle power lines with thermistor) | U/V/W/ Ground wire |
| 6 | Intake air(Spindle loose knife0.5-0.6MPa) | Ф6 |
| 7 | Sensor(spindle tool change signals 24V) | Broach / loose knife |
| 8 | Fan (spindle cooling) | 12V |
6)PTC140Temperature coefficient thermistor parameters
Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection.
| Parameter name | Parameter symbol | Single core | Three core Series connection | Unit |
| Maximum DC working temperature | Umax | 30 | 30 | V |
| Rated control temperature | Tk | Designed according to user | ℃ |
| Rated control temperature tolerance |  T1 | ±5℃ | ±5℃ | ℃ |
| Rated control temperature tolerance |  T2 | ±0.5℃ | ±0.5℃ | ℃ |
| Resistance value on 25℃ | R25 | ≤100 | ≤300 | Ω |
Rated control temperature
on -5℃resistance value | Tk-5℃ | ≤550 | ≤1600 | Ω |
Rated control temperature
on +5℃resistance value | Tk+5℃ | ≥1330 | ≥4000 | Ω |
Rated control temperature
on +15℃resistance value | Tk+15℃ | ≥4 | ≥12 | KΩ |
| Thermal response time | Ta | ≤5 | ≤5 | S |
| Dielectric strength | Uis | AC2.5 | AC2.5 | KV |
| Maximum control temperature | Tkmax | 180 | 180 | ℃ |
| Maximum allowable storage temperature | Tmax | 180 | 180 | ℃ |
| Minimum allowable storage temperature | Tmin | -40 | -40 | ℃ |
7) ProductTool ChangeSignalsDescription
Sensor Model (0-24V, PNP),The spindle built two sensors.wiring Diagram is as follows:
1. Response broach knife signal, when theknife handleis hang,black sensor output signal;
2. Response loose knife signal, when theknife jawsopen,black sensor output signal;
